The D2v 3D pushes the boundaries on what you expect from music and home theater performance. With the unparalleled flexibility you have to come to expect from Anthem processors, it provides both the versatility and adjustability you need to ale all of your digital video components work together seamlessly. The results are spectacular.
Ready for 3D
From riding the third dimension on light cycles in the movie Tron, to racing through the 3D jungles of Pandora in Avatar, the movie experience is always better in triple dimensions. 3D video has a different structure than traditional video so it must pass through the A/V processor without being affected. The new Anthem D2v circuit board automatically detects the presence of 3D video and go into passthrough mode as per a source menu option for video output configuration, passing the 3D HDMI signal from a 3D Blu-ray player to a 3D TV at resolutions up to 1080p. For additional convenience, in passthrough mode the output refresh rate is now automatically matched to the source’s frame refresh rate which is useful for sources that output a mix between 24, 50 and 60 Hz.
It’s now 3D equipped. Fully featured 7.1-channel audio and video processor, 8 HDMI Inputs and 2 Parallel HDMI outputs with the top four ports (HDMI 1 through 4) and top output (HDMI 1) supporting true bypass sensing 3D inputs automatically, Dolby TrueHD, DTS-HD Master Audio, PCM 24/192, highest quality 1080p upscaling with 1080p24 compatibility, Anthem Room Correction, premium quality A/D and D/A converters, 24-bit/192 kHz upsampling on all channels in main zone, two stereo zones.
VIDEO SWITCHING | |
---|---|
Composite And S-Video | 70 MHz |
Component Y | 110 MHz |
Component Pr | 90 MHz |
Component Pb | 80 MHz |
ANALOG AUDIO | |
Input Impedance | 20 kΩ |
Output Impedance Main-RCA | 300 Ω |
Output Impedance XLR | 600 Ω |
Output Impedance Zones 2/3 and Record | 51 Ω |
Rated Input | 2.0 Vrms |
Maximum Input | 5.3 Vrms |
Minimum Load | 5 kΩ |
Rated Output (100 KΩ Load) | 2.0 Vrms |
Maximum Output RCA | 6.3 Vrms |
Maximum Output XLR | 12.6 Vrms |
Headphone Output | 100 mW into 32 Ω at 0.2% THD+N |
Volume Control Range Main | - 95.5 dB to +31.5 dB (in 0.5 dB increments) |
Volume Control Range Zone 2/3 and Headphone | - 62.5 dB to +10.0 dB (in 1.25 dB increments) |
Crosstalk (At 1 KHz) | 82 dB between channels; 86 dB between inputs |
XLR Pin Configuration | Pin 1: Ground, Pin 2: Positive, Pin 3: Negative |
Crossover | |
High-Pass Slope (small speaker setting) | 12 dB/octave (2nd order) |
Low-Pass Slope (subwoofer) | 24 dB/octave (4th order) |
Frequency (adjustable) | 25 Hz to 160 Hz (in 5 Hz increments) |
Tone Control | |
Fliter Type | Shelf |
Range | +/- 12 dB |
Bass Turnover Frequency | 200 Hz |
Treble Turnover Frequency | 2 kHz |
ZONE 2 AND ZONE 3 PATHS | |
Frequency Response And Bandwidth | 20 Hz to 20 kHz (+0 -0.1 dB), 3 Hz to 140 kHz (+0 -3 dB) |
THD+N (At Rated Input And Output) | 0.06% (80 kHz BW) |
IMD (CCIF At 15 KHz And 16 KHz) | 0.06% |
S/N Ratio (Ref. 2.0 Vrms, IEC-A Filter) | 97 dB |
FM TUNER | |
Sensitivity 50 dB S/N | 13 dBµ typical, 25 dBµ max. |
Sensitivity IHF | 10 dBµ typical, 20 dBµ max. |
S/N Ratio Mono | 75 dB typical, 65 dB min. |
S/N Ratio Stereo | 69 dB typical, 60 dB min. |
Distortion Mono | 0.2% typical, 1.0% max. |
Distortion Stereo | 0.3% typical, 1.5% max. |
Stereo Separation | 40 dB typical, 25 dB min. |
Alternate Channel Selectivity (+/- 400 KHz) | 70 dB typical, 60 dB min. |
Frequency Response | 25 Hz to 15 kHz (+0 -2 dB) |
AM TUNER | |
Sensitivity (20 DB S/N) | 49 dBµ typical, 56 dBµ max. |
S/N Ratio | 50 dB typical, 43 dB min. |
Distortion | 0.7% typical, 2.0% max. |
One-Signal Selectivity (+/- 10 KHz) | 24 dB typical, 18 dB min. |
Control | |
Infra Red Carrier Frequency | 38 kHz |
Infra Red Maximum 12 V Supply Current | 150 mA |
Infra Red Maximum Emitter Current | 60 mA per output |
RS-232 Interface Connection | DB-9F, straight-wired |
RS-232 Interface Pinout (D2v side) | Pin 2: Tx, Pin 3: Rx, Pin 5: Ground |
RS-232 Interface Baud Rate | 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200 |
RS-232 Interface Configuration | 8 data bits, 1 stop bit, no parity bits, flow control (RTS/CTS, none) |
Trigger Outputs Polarity | tip positive, sleeve ground |
Trigger Outputs Maximum Current at 12 VDC | 300 mA between all three triggers |
Trigger Outputs Sequential Delay | 250 ms |
POWER REQUIREMENT | |
Consumption | Maximum 170 W |